Installation & Care

MEK PPV JT Side Body Installation


MEK PPV JL Hood Installation


Nano-Hold Technology - NEW Quick Install Version


Nano-Hold Technology - Complete Guide


Magnetic Armor Tips & Tricks

 

MEK ARMOR INSTALLATION GUIDE

BEFORE YOU BEGIN

  • Cleanliness is key: Ensure both your vehicle and the gel-back (nano-hold) Armor are clean and dry.
  • Proper bonding: The cleaner the surface, the stronger the adhesion.
  • Trail-use only: MEK Armor is designed for off-road trail use. Remove regularly to clean vehicle and Armor.

TOOLS NEEDED

  • Clean microfiber cloths
  • Diluted isopropyl alcohol (for surface prep)
  • Water for rinsing
  • Mild soap (optional)

PREP YOUR VEHICLE

  1. Remove waxes & coatings:
    • Clean with a 1:1 water and isopropyl alcohol mixture.
    • Use a wet microfiber cloth to wipe the surface.
    • Follow with a dry microfiber cloth before it dries.
  2. Check for non-stick coatings:
    • If your vehicle has ceramic or Teflon coatings, test with a MEK sample logo for adhesion.

INSTALLING MAGNETIC ARMOR

  • Install time: 15-30 minutes
  • Clean vehicle surface and apply directly before hitting the trails.

 INSTALLING GEL-BACK ARMOR

  • Install time: 30-90 minutes
  1. Unroll Armor:
    • Place image side up.
    • Peel from a corner using your fingernail.
  2. Align & apply:
    • Hold panel over correct area.
    • Gently stick one edge to the vehicle.
    • Align, press and smooth from opposite edge inward.
    • Re-lift the first edge and reapply using center-out fanning motion.
  3. To reposition:
    • Peel slowly, straight back and perpendicular to the vehicle.
    • For Jeep panels with letter cutouts, peel from top and bottom toward the center.
  4. Clean the gel side:
    • Rinse with water, gently rub with fingers.
    • Let air dry completely.

REMOVING ARMOR

  • Always pull panels slowly and evenly.
  • Avoid tugging from one corner or side only.
  • Store clean panels flat or in MEK carry bag.

TROUBLESHOOTING

  • Air bubbles? Pull back and reinstall from the bubble area.
  • Champagne bubbles? Normal and usually disappear after a few days.
  • Misalignment? Gently peel off and repeat install process.

CARE & MAINTENANCE

  • Wipe down regularly with a clean microfiber cloth.
  • Remove during high humidity, rain, snow, or after salt exposure.
  • Reactivating gel: Rinse and air dry to restore adhesion.
  • Storage: Lay flat in a cool, dry place away from sunlight. Do not fold.
  • Temperature limits: Rated for 15°F to 180°F.

WARRANTY

  • 1-year limited warranty for fade and craftsmanship.
  • Individual panel replacement available.

NEW! MEK PPV (Paint Protective Vinyl) INSTALLATION

WHAT YOU NEED

  • Vinegar-based cleaner (1 part vinegar, 4 parts water, mild dish soap)
  • Slip/tack spray (1 part alcohol, 4-7 parts water, few drops dish soap)
  • Microfiber cloth, squeegee, scissors, blow dryer

INSTALL STEPS

  1. Clean the vehicle thoroughly and let it dry.
  2. Spray slip/tack solution on both sticky side of vinyl and the vehicle.
  3. Float vinyl into position and align properly.
  4. Use squeegee from center out to remove air and solution.
  5. Press edges down firmly. Add gentle heat if needed.
  6. Remove & realign if needed, avoid creasing the vinyl.
  7. Final step: Wipe away residue and gently heat any stretched areas to shrink smooth.

REMOVAL

  • Heat a corner and gently peel back.
  • Clean vehicle surface after removal.

IMPORTANT NOTES

  • Do not install MEK Armor over gloss ink vinyl.
  • Vinyl offers light protection. Use removable Armor for full trail coverage.
  • MEK PPV is not a full wrap. Paint fade may occur. Store in shade when possible.

For questions or support, contact MEK Magnet customer service.